| 01-16 |
Air filter not connected |
Air filter not properly attached |
Check and secure the air filter; replace if necessary |
| 01-17 |
Clogged air filter |
Dirty air filter blocking airflow |
Clean or replace the clogged air filter |
| 02-16 |
No hydraulic discharge filter connected |
Missing or improperly installed hydraulic discharge filter |
Install a new hydraulic discharge filter |
| 02-17 |
Clogged hydraulic discharge filter |
Hydraulic discharge filter clogged with contaminants |
Clean or replace the clogged hydraulic discharge filter |
| 03-09 |
Low battery voltage |
Battery is low on charge or faulty |
Charge or replace the battery if necessary |
| 03-10 |
High battery voltage |
Battery voltage too high |
Disconnect and have the battery checked by a professional |
| 03-11 |
Extremely high battery voltage |
Dangerously high battery voltage |
Disconnect and seek professional assistance immediately |
| 03-14 |
Extremely low battery voltage |
Battery almost depleted or faulty |
Charge or replace the battery if needed |
| 03-22 |
Battery voltage below maximum permissible |
Battery voltage too low |
Check battery health and charging system; replace if needed |
| 04-09 |
Low oil pressure in the engine |
Engine oil leak or low oil level |
Check oil level and system; seek professional assistance |
| 04-14 |
Extremely high engine oil pressure |
Engine overheating or oil passages blocked |
Stop engine, let it cool, and seek professional help |
| 04-15 |
Engine oil pressure at emergency shutdown level |
Critical engine oil pressure |
Stop engine immediately; inspect oil system; professional help |
| 04-21 |
Engine oil pressure above maximum permissible |
Engine oil pressure too high |
Stop engine, let it cool, and seek professional help |
| 04-22 |
Engine oil pressure below maximum permissible |
Engine oil pressure too low |
Stop engine; check oil level and leaks; professional help |
| 05-09 |
Low recharge pressure in hydraulic system |
Hydraulic fluid leak or system component issue |
Check fluid level and leaks; seek professional assistance |
| 05-14 |
Extremely low recharge pressure in hydraulic system |
Severe hydraulic system problem |
Stop using machine; seek professional inspection and repair |
| 05-15 |
Recharge pressure at engine emergency shutdown level |
Critical hydraulic system pressure |
Stop using machine; seek professional inspection and repair |
| 05-21 |
Recharge pressure above maximum permissible |
Hydraulic system pressure too high |
Stop using machine; have professional adjust pressure |
| 05-22 |
Recharge pressure below maximum permissible |
Hydraulic system pressure too low |
Have professional inspect and adjust hydraulic system |
| 06-10 |
High engine speed |
Engine running at a high speed |
Adjust engine speed to a normal level |
| 06-11 |
Extremely high engine speed |
Engine running at a dangerously high speed |
Immediately reduce engine speed to a safe level |
| 06-13 |
No engine speed signal |
Lack of signal indicating the engine speed |
Check engine speed sensor; repair or replace if necessary |
| 06-15 |
Engine speed at the emergency shutdown level |
Engine speed reached a critical level |
Stop the engine to avoid damage |
| 06-18 |
Engine speed outside the permissible limits |
Engine speed is not within safe operating limits |
Adjust engine speed to fall within safe parameters |
| 07-10 |
High oil temperature in the hydraulic system |
Hydraulic system oil temperature is high |
Check hydraulic system cooling; resolve any issues |
| 07-11 |
Extremely high oil temperature in hydraulic system |
Hydraulic system oil temperature dangerously high |
Stop using the machine; seek professional help immediately |
| 07-15 |
Oil temperature in hydraulic system at emergency shutdown level |
Hydraulic system oil temperature at a critical point |
Stop the machine immediately to prevent further damage |
| 07-21 |
Oil temperature in hydraulic system above maximum permissible |
Hydraulic system oil temperature too high |
Stop using the machine; have professional check and fix issue |
| 07-22 |
Oil temperature in hydraulic system below maximum permissible |
Hydraulic system oil temperature too low |
Have professional inspect and address hydraulic system issue |
| 08-10 |
High engine coolant temperature |
Engine coolant temperature is high |
Check cooling system; resolve any issues |
| 08-11 |
Extremely high engine coolant temperature |
Engine coolant temperature dangerously high |
Stop the engine; seek immediate professional assistance |
| 08-15 |
Engine coolant temperature at emergency shutdown level |
Engine coolant temperature critical |
Stop the engine immediately to prevent further damage |
| 08-21 |
Engine coolant temperature above maximum permissible |
Engine coolant temperature too high |
Stop using the machine; have professional check and fix issue |
| 08-22 |
Engine coolant temperature below maximum permissible |
Engine coolant temperature too low |
Have professional inspect and address engine coolant issue |
| 09-09 |
Low fuel level |
Low fuel level in the tank |
Refuel the machine to an adequate level |
| 09-21 |
Fuel level above maximum permissible |
Fuel level is higher than the safe limit |
Check fuel system; resolve any issues |
| 09-22 |
Fuel level below maximum permissible |
Fuel level is lower than the safe limit |
Refuel the machine to an adequate level |
| 11-05 |
Safety frame sensor closed to the battery |
Safety frame sensor detecting a closed circuit |
Check sensor connection and wiring; repair or replace as needed |
| 11-06 |
Security frame sensor closed to mass |
Security frame sensor detecting a closed circuit |
Check sensor connection and wiring; repair or replace as needed |
| 12-21 |
Signal PWM Controller front additional hydraulics at upper limit of the range |
Hydraulic system signal at upper limit |
Check front additional hydraulics system; adjust if necessary |
| 12-22 |
Signal PWM Controller front additional hydraulics at lower limit of the range |
Hydraulic system signal at lower limit |
Check front additional hydraulics system; adjust if necessary |
| 12-23 |
Signal PWM Controller front additional hydraulics not in neutral position |
Hydraulic system signal not in neutral |
Check front additional hydraulics system; resolve any issues |
| 13-05 |
Retaining solenoid of fuel cutoff closed on battery |
Issue with fuel cutoff solenoid circuit |
Check and repair the fuel cutoff solenoid circuit |
| 13-06 |
Retaining solenoid of fuel cutoff closed to mass |
Issue with fuel cutoff solenoid circuit |
Check and repair the fuel cutoff solenoid circuit |
| 13-07 |
Circuit Break solenoid cutoff fuel |
Issue with fuel cutoff solenoid circuit |
Check and repair the fuel cutoff solenoid circuit |
| 14-02 |
Motorcyclist the fuel cutoff solenoid, erroneous switching on |
Incorrect activation of fuel cutoff solenoid |
Check and repair the fuel cutoff solenoid |
| 14-03 |
Motorcyclist the fuel cutoff solenoid, erroneous shutdown |
Incorrect deactivation of fuel cutoff solenoid |
Check and repair the fuel cutoff solenoid |
| 15-02 |
Motorcyclist solenoid lock thrust, erroneous inclusion |
Incorrect activation of lock thrust solenoid |
Check and repair the lock thrust solenoid |
| 15-03 |
Motorcyclist solenoid lock thrust, erroneous shutdown |
Incorrect deactivation of lock thrust solenoid |
Check and repair the lock thrust solenoid |
| 16-05 |
The holding solenoid lock is closed on the battery |
Issue with the holding solenoid circuit |
Check and repair the holding solenoid circuit |
| 16-06 |
The holding solenoid of the thrust lock is closed to the mass |
Issue with the holding solenoid circuit |
Check and repair the holding solenoid circuit |
| 16-07 |
Tearing chain restraint solenoid lock thrust |
Issue with the holding solenoid circuit |
Check and repair the holding solenoid circuit |
| 17-05 |
The hydraulic valve solenoid is closed to the battery |
Issue with hydraulic valve solenoid circuit |
Check and repair the hydraulic valve solenoid circuit |
| 17-06 |
The hydraulic valve solenoid is closed to the mass |
Issue with hydraulic valve solenoid circuit |
Check and repair the hydraulic valve solenoid circuit |
| 17-07 |
Rupture of the solenoid circuit of the hydraulic shutoff valve |
Issue with hydraulic valve solenoid circuit |
Check and repair the hydraulic valve solenoid circuit |
| 18-05 |
The spool solenoid is closed on the battery |
Issue with the spool solenoid circuit |
Check and repair the spool solenoid circuit |
| 18-06 |
The spool solenoid is closed to the mass |
Issue with the spool solenoid circuit |
Check and repair the spool solenoid circuit |
| 18-07 |
Spool solenoid circuit break |
Issue with the spool solenoid circuit |
Check and repair the spool solenoid circuit |
| 19-02 |
Bucket positioning solenoid, erroneous switching on |
Incorrect activation of bucket positioning solenoid |
Check and repair the bucket positioning solenoid |
| 19-03 |
Bucket positioning solenoid, erroneous shutdown |
Incorrect deactivation of bucket positioning solenoid |
Check and repair the bucket positioning solenoid |
| 20-02 |
Speed switching solenoid, erroneous switching on |
Incorrect activation of speed switching solenoid |
Check and repair the speed switching solenoid |
| 20-03 |
Speed switch solenoid, erroneous shutdown |
Incorrect deactivation of speed switching solenoid |
Check and repair the speed switching solenoid |
| 21-02 |
Glow plugs, erroneous inclusion |
Incorrect activation of glow plugs |
Check and repair the glow plugs |
| 21-03 |
Glow plugs, erroneous shutdown |
Incorrect deactivation of glow plugs |
Check and repair the glow plugs |
| 22-02 |
Starter, erroneous inclusion |
Incorrect activation of the starter |
Check and repair the starter circuit |
| 22-03 |
Starter, erroneous shutdown |
Incorrect deactivation of the starter |
Check and repair the starter circuit |
| 23-02 |
Rear base solenoid, erroneous switching on |
Incorrect activation of rear base solenoid |
Check and repair the rear base solenoid circuit |
| 23-03 |
Rear base solenoid, erroneous shutdown |
Incorrect deactivation of rear base solenoid |
Check and repair the rear base solenoid circuit |
| 24-02 |
Rear Pull Solenoid, erroneous switching on |
Incorrect activation of rear pull solenoid |
Check and repair the rear pull solenoid circuit |
| 24-03 |
Rear Pull Solenoid, erroneous shutdown |
Incorrect deactivation of rear pull solenoid |
Check and repair the rear pull solenoid circuit |
| 25-02 |
Rear auxiliary proportional solenoid, erroneous inclusion |
Incorrect activation of rear auxiliary proportional solenoid |
Check and repair the rear auxiliary proportional solenoid circuit |
| 25-03 |
Rear auxiliary proportional solenoid, erroneous shutdown |
Incorrect deactivation of rear auxiliary proportional solenoid |
Check and repair the rear auxiliary proportional solenoid circuit |
| 26-02 |
Erroneous inclusion of the front base solenoid |
Incorrect activation of front base solenoid |
Check and repair the front base solenoid circuit |
| 26-03 |
Erroneous shutdown of the front base solenoid |
Incorrect deactivation of front base solenoid |
Check and repair the front base solenoid circuit |
| 27-02 |
Erroneous inclusion of the front Stock Solenoid |
Incorrect activation of front stock solenoid |
Check and repair the front stock solenoid circuit |
| 27-03 |
Erroneous shutdown of the front Stock Solenoid |
Incorrect deactivation of front stock solenoid |
Check and repair the front stock solenoid circuit |
| 28-02 |
Erroneous inclusion of solenoid Divertera |
Incorrect activation of diverter solenoid |
Check and repair the diverter solenoid circuit |
| 28-03 |
Incorrect solenoid shutdown Divertera |
Incorrect deactivation of diverter solenoid |
Check and repair the diverter solenoid circuit |
| 29-02 |
Large feed solenoid, erroneous switching on |
Incorrect activation of large feed solenoid |
Check and repair the large feed solenoid circuit |
| 29-03 |
Large feed solenoid, erroneous shutdown |
Incorrect deactivation of large feed solenoid |
Check and repair the large feed solenoid circuit |
| 30-28 |
Controller memory failure |
Issue with the loader’s controller memory |
Professional diagnosis and repair of the controller memory |
| 31-28 |
Recovery mode failure |
Issue with the loader’s recovery mode |
Professional diagnosis and repair of the recovery mode |
| 32-04 |
Advanced Management (ACS) not reported to the controller Bobcat |
Issue with the loader’s Advanced Management (ACS) system |
Professional diagnosis and repair of the Advanced Management (ACS) system |
| 32-23 |
ACS Advanced Management Not calibrated |
Advanced Management (ACS) system not calibrated |
Calibration of the Advanced Management (ACS) system |
| 32-31 |
Failure of the actuating mechanism of inclination |
Issue with the loader’s actuating mechanism of inclination |
Check and repair the actuating mechanism of inclination |
| 32-32 |
Malfunction of the electrical wiring of the actuating mechanism of inclination |
Issue with electrical wiring of the actuating mechanism of inclination |
Check and repair the electrical wiring of the actuating mechanism of inclination |
| 32-33 |
Failure of the electrical wiring of the bucket tilting handle |
Issue with electrical wiring of the bucket tilting handle |
Check and repair the electrical wiring of the bucket tilting handle |
| 32-34 |
Executive tilting mechanism not in neutral position |
Actuating mechanism of tilting not in the neutral position |
Check and adjust the actuating mechanism of tilting |
| 32-35 |
Handle/Bucket tilt pedal not in neutral position |
Handle/Bucket tilt pedal not in the neutral position |
Check and adjust the handle/bucket tilt pedal |
| 32-36 |
Failure of the actuating mechanism of lifting |
Issue with the loader’s actuating mechanism of lifting |
Check and repair the actuating mechanism of lifting |
| 32-37 |
Malfunction of electrical wiring of the actuating mechanism of lifting |
Issue with electrical wiring of the actuating mechanism of lifting |
Check and repair the electrical wiring of the actuating mechanism of lifting |
| 32-38 |
Failure of the electrical wiring of the boom handle |
Issue with electrical wiring of the boom handle |
Check and repair the electrical wiring of the boom handle |
| 32-39 |
Executive lifting mechanism not in neutral position |
Actuating mechanism of lifting not in the neutral position |
Check and adjust the actuating mechanism of lifting |
| 32-40 |
Arm/Boom lift pedal not in neutral position |
Arm/Boom lift pedal not in the neutral position |
Check and adjust the arm/boom lift pedal |
| 32-41 |
No connection |
No connection with the specified component |
Check and establish the connection with the specified component |
| 32-49 |
Executive lifting mechanism closed to mass |
Actuating mechanism of lifting closed to mass |
Check and repair the actuating mechanism of lifting |
| 32-50 |
The executive tilting mechanism is closed to mass |
Actuating mechanism of tilting closed to mass |
Check and repair the actuating mechanism of tilting |
| 32-51 |
Actuator lifting mechanism closed on the battery |
Actuating mechanism of lifting closed on the battery |
Check and repair the actuating mechanism of lifting |
| 32-52 |
The actuator tilting mechanism is closed to the battery |
Actuating mechanism of tilting closed on the battery |
Check and repair the actuating mechanism of tilting |
| 32-53 |
Handle/Boom lift pedal closed to mass |
Handle/Boom lift pedal closed to mass |
Check and repair the handle/boom lift pedal |
| 32-54 |
Handle/Bucket tilt pedal closed to mass |
Handle/Bucket tilt pedal closed to mass |
Check and repair the handle/bucket tilt pedal |
| 32-54 |
Handle/Bucket tilt pedal closed to mass |
Issue with the handle/bucket tilt pedal circuit |
Check and repair the handle/bucket tilt pedal circuit |
| 32-55 |
Arm/Boom lift pedal closed on battery |
Issue with the arm/boom lift pedal circuit |
Check and repair the arm/boom lift pedal circuit |
| 32-56 |
The handle/bucket tilt pedal is closed to the battery |
Issue with the handle/bucket tilt pedal circuit |
Check and repair the handle/bucket tilt pedal circuit |
| 32-57 |
Reduced performance of the lifting actuation mechanism |
Issue with the lifting actuation mechanism |
Check and repair the lifting actuation mechanism circuit |
| 32-58 |
Reduced performance of the executive tilt mechanism |
Issue with the executive tilt mechanism |
Check and repair the executive tilt mechanism circuit |
| 32-59 |
Wrong direction of the actuating mechanism of lifting |
Issue with the actuating mechanism of lifting |
Check and repair the actuating mechanism of lifting |
| 32-60 |
Wrong direction of the executive tilt mechanism |
Issue with the executive tilt mechanism |
Check and repair the executive tilt mechanism circuit |
| 32-61 |
The lock of arms is closed to mass |
Issue with the lock of arms circuit |
Check and repair the lock of arms circuit |
| 32-62 |
The lock of Arms is closed on the battery |
Issue with the lock of arms circuit |
Check and repair the lock of arms circuit |
| 32-63 |
The chain of locking pedals is closed to the mass |
Issue with the chain of locking pedals circuit |
Check and repair the chain of locking pedals circuit |
| 32-64 |
The chain of locking pedals is closed to the battery |
Issue with the chain of locking pedals circuit |
Check and repair the chain of locking pedals circuit |
| 32-65 |
Sensor supply voltage outside the permissible limits |
Issue with the sensor supply voltage |
Check and address the sensor supply voltage |
| 32-66 |
Battery voltage out of the allowable limits |
Issue with the loader’s battery voltage |
Check and address the loader’s battery voltage |
| 32-67 |
Switched during Operation |
Issue with the control switches during operation |
Check and repair any faulty control switches |
| 32-68 |
Boom Boom ARM Information error |
Issue with the boom arm information |
Check and address the boom arm information |
| 32-69 |
The switch of control modes has switched during operation |
Issue with the control mode switch circuit |
Check and repair the control mode switch circuit |
| 32-70 |
The chain of the right handle of motion is closed to mass |
Issue with the chain of the right handle of motion circuit |
Check and repair the chain of the right handle of motion circuit |
| 32-71 |
Circuit of the right handle of movement is closed on the battery |
Issue with the circuit of the right handle of movement |
Check and repair the circuit of the right handle of movement |
| 33-23 |
Main controller (Controller Bobcat) Not programmed |
Main controller not programmed |
Program the main controller |
| 34-04 |
The keypad with a button run is not reported to the controller Bobcat |
Issue with the keypad circuit |
Check and repair the keypad circuit |
| 35-02 |
Speed fan switch, erroneous switching on |
Incorrect activation of the fan speed switch |
Check and repair the fan speed switch circuit |
| 35-03 |
Speed fan switch, erroneous shutdown |
Incorrect deactivation of the fan speed switch |
Check and repair the fan speed switch circuit |
| 36-48 |
Multiple ACD controllers are connected |
Multiple ACD controllers connected |
Check and address multiple ACD controllers |
| 37-02 |
Speed additional speed switch, erroneous switching on |
Incorrect activation of the additional speed switch |
Check and repair the additional speed switch circuit |
| 37-03 |
Speed additional speed switch, erroneous shutdown |
Incorrect deactivation of the additional speed switch |
Check and repair the additional speed switch circuit |
| 38-04 |
No connection to Joystick controller |
No connection with the joystick controller |
Check and establish the connection with the joystick controller |
| 38-05 |
The x-axis of the left joystick is not in a neutral position |
Left joystick’s x-axis not in neutral position |
Check and adjust the left joystick’s x-axis |
| 38-06 |
The X-axis of the right joystick is not in a neutral position |
Right joystick’s X-axis not in neutral position |
Check and adjust the right joystick’s X-axis |
| 38-07 |
The Y-axis of the left joystick is not in a neutral position |
Left joystick’s Y-axis not in neutral position |
Check and adjust the left joystick’s Y-axis |
| 38-08 |
The Y-axis of the right joystick is not in a neutral position |
Right joystick’s Y-axis not in neutral position |
Check and adjust the right joystick’s Y-axis |
| 38-09 |
Control mode switch-circuit to the battery or to the mass |
Issue with control mode switch circuit |
Check and repair the control mode switch circuit |
| 38-11 |
Executive lifting mechanism not in neutral position |
Actuating mechanism of lifting not in neutral position |
Check and adjust the actuating mechanism of lifting |
| 38-12 |
Executive tilting mechanism not in neutral position |
Actuating mechanism of tilting not in neutral position |
Check and adjust the actuating mechanism of tilting |
| 38-13 |
Failure of the actuating mechanism of lifting |
Issue with the actuating mechanism of lifting |
Check and repair the actuating mechanism of lifting |
| 38-14 |
Failure of the actuating mechanism of inclination |
Issue with the actuating mechanism of inclination |
Check and repair the actuating mechanism of inclination |
| 38-15 |
Right Wheel speed control failure |
Issue with the right wheel speed control |
Check and repair the right wheel speed control circuit |
| 38-16 |
Faulty wiring for the speed of the left wheel |
Issue with the left wheel speed control |
Check and repair the left wheel speed control circuit |
| 38-17 |
Reduced performance of the executive tilt mechanism |
Issue with the executive tilt mechanism |
Check and repair the executive tilt mechanism circuit |
| 38-18 |
Reduced performance of the lifting actuation mechanism |
Issue with the lifting actuation mechanism |
Check and repair the lifting actuation mechanism circuit |
| 38-19 |
The X-axis of the left joystick, behind the upper bound of the range |
Left joystick’s X-axis out of range |
Check and adjust the left joystick’s X-axis |
| 38-20 |
X-axis of the right joystick, beyond the lower bound of the range |
Right joystick’s X-axis out of range |
Check and adjust the right joystick’s X-axis |
| 38-21 |
The Y-axis of the left joystick, behind the upper bound of the range |
Left joystick’s Y-axis out of range |
Check and adjust the left joystick’s Y-axis |
| 38-22 |
The Y-axis of the right joystick, behind the upper bound of the range |
Right joystick’s Y-axis out of range |
Check and adjust the right joystick’s Y-axis |
| 38-23 |
Signal of the front right control sensor outside the upper boundary of the range |
Issue with the front right control sensor |
Check and calibrate the front right control sensor |
| 38-24 |
Signal of the front left control sensor at the upper limit of the range |
Issue with the front left control sensor |
Check and calibrate the front left control sensor |
| 38-25 |
Signal of the rear right control sensor at the upper limit of the range |
Issue with the rear right control sensor |
Check and calibrate the rear right control sensor |
| 38-26 |
Signal of the rear left control sensor at the upper limit of the range |
Issue with the rear left control sensor |
Check and calibrate the rear left control sensor |
| 38-27 |
Signal of the actuating mechanism of lifting at the upper boundary of the range |
Issue with the actuating mechanism of lifting |
Check and calibrate the actuating mechanism of lifting |
| 38-28 |
Signal of the executive mechanism of inclination at the upper boundary of the range |
Issue with the executive mechanism of inclination |
Check and calibrate the executive mechanism of inclination |
| 38-29 |
X-axis of the left joystick, behind the lower bound of the range |
Issue with the left joystick’s X-axis |
Check and calibrate the left joystick’s X-axis |
| 38-30 |
X-axis of the right joystick, beyond the lower bound of the range |
Issue with the right joystick’s X-axis |
Check and calibrate the right joystick’s X-axis |
| 38-31 |
Y-axis of the left joystick, beyond the lower bound of the range |
Issue with the left joystick’s Y-axis |
Check and calibrate the left joystick’s Y-axis |
| 38-32 |
Y-axis of the right joystick, beyond the lower bound of the range |
Issue with the right joystick’s Y-axis |
Check and calibrate the right joystick’s Y-axis |
| 38-33 |
Signal of the front right control sensor at the lower limit of the range |
Issue with the front right control sensor |
Check and calibrate the front right control sensor |
| 38-34 |
Signal of the front left control sensor at the lower limit of the range |
Issue with the front left control sensor |
Check and calibrate the front left control sensor |
| 38-35 |
Signal of the rear right control sensor at the lower limit of the range |
Issue with the rear right control sensor |
Check and calibrate the rear right control sensor |
| 38-36 |
Signal of the rear left control sensor at the lower limit of the range |
Issue with the rear left control sensor |
Check and calibrate the rear left control sensor |
| 38-37 |
Power supply “1” 5-volt sensor, behind the lower boundary of the range |
Issue with the power supply “1” 5-volt sensor |
Check and address the power supply “1” 5-volt sensor |
| 38-38 |
Power supply “2” 5-volt sensor, behind the lower boundary of the range |
Issue with the power supply “2” 5-volt sensor |
Check and address the power supply “2” 5-volt sensor |
| 38-39 |
Executive lifting mechanism closed to mass/beyond the lower boundary of the range |
Issue with the executive lifting mechanism |
Check and repair the executive lifting mechanism circuit |
| 38-40 |
The executive tilt mechanism is closed to the mass/signal at the lower limit of the range |
Issue with the executive tilt mechanism |
Check and repair the executive tilt mechanism circuit |
| 38-41 |
Wrong direction of the executive tilt mechanism |
Issue with the executive tilt mechanism |
Check and repair the executive tilt mechanism circuit |
| 38-42 |
Wrong direction of the actuating mechanism of lifting |
Issue with the actuating mechanism of lifting |
Check and repair the actuating mechanism of lifting |
| 38-43 |
The solenoid of the left front drive, erroneous switching on |
Issue with the solenoid of the left front drive |
Check and repair the solenoid of the left front drive |
| 38-44 |
Solenoid of left reversible drive, erroneous switching on |
Issue with the solenoid of the left reversible drive |
Check and repair the solenoid of the left reversible drive |
| 38-45 |
Right front drive solenoid, erroneous switching on |
Issue with the right front drive solenoid |
Check and repair the right front drive solenoid |
| 38-46 |
Right reverse actuator solenoid, erroneous switching on |
Issue with the right reverse actuator solenoid |
Check and repair the right reverse actuator solenoid |
| 38-47 |
Front right control solenoid, erroneous switching on |
Issue with the front right control solenoid |
Check and repair the front right control solenoid |
| 38-48 |
Front left solenoid control, erroneous switching on |
Issue with the front left solenoid control |
Check and repair the front left solenoid control |
| 38-49 |
Rear right control solenoid, erroneous switching on |
Issue with the rear right control solenoid |
Check and repair the rear right control solenoid |
| 38-50 |
Rear left solenoid control, erroneous switching on |
Issue with the rear left solenoid control |
Check and repair the rear left solenoid control |
| 38-51 |
Control system pressure solenoid, erroneous switching on |
Issue with the control system pressure solenoid |
Check and repair the control system pressure solenoid |
| 38-52 |
Reversing signal, erroneous switching on |
Issue with the reversing signal |
Check and repair the reversing signal circuit |
| 38-53 |
Left Front drive solenoid, erroneous shutdown |
Issue with the left front drive solenoid |
Check and repair the left front drive solenoid |
| 38-54 |
Solenoid of left reversible drive, erroneous shutdown |
Issue with the solenoid of the left reversible drive |
Check and repair the solenoid of the left reversible drive |
| 38-55 |
Right front drive solenoid, erroneous shutdown |
Issue with the right front drive solenoid |
Check and repair the right front drive solenoid |
| 38-56 |
Right reverse actuator solenoid, erroneous shutdown |
Issue with the right reverse actuator solenoid |
Check and repair the right reverse actuator solenoid |
| 38-57 |
Front right extension control solenoid, erroneous shutdown |
Issue with the front right extension control solenoid |
Check and repair the front right extension control solenoid |
| 38-58 |
Front right retraction control solenoid, erroneous shutdown |
Issue with the front right retraction control solenoid |
Check and repair the front right retraction control solenoid |
| 38-59 |
Front left solenoid of extension control, erroneous shutdown |
Issue with the front left solenoid of extension control |
Check and repair the front left solenoid of extension control |
| 38-60 |
Front left solenoid control retraction, erroneous shutdown |
Issue with the front left solenoid control retraction |
Check and repair the front left solenoid control retraction |
| 38-61 |
Rear right extension control solenoid, erroneous shutdown |
Issue with the rear right extension control solenoid |
Check and repair the rear right extension control solenoid |
| 38-62 |
Rear right retraction control solenoid, erroneous shutdown |
Issue with the rear right retraction control solenoid |
Check and repair the rear right retraction control solenoid |
| 38-63 |
Rear left solenoid control, erroneous shutdown |
Issue with the rear left solenoid control |
Check and repair the rear left solenoid control |
| 38-64 |
Rear left solenoid control retraction, erroneous shutdown |
Issue with the rear left solenoid control retraction |
Check and repair the rear left solenoid control retraction |
| 38-65 |
Control system pressure solenoid, erroneous shutdown |
Issue with the control system pressure solenoid |
Check and repair the control system pressure solenoid |
| 38-66 |
Reversing signal, erroneous shutdown |
Issue with the reversing signal |
Check and repair the reversing signal circuit |
| 38-67 |
No messages from controller Bobcat |
Communication issue between the Bobcat controller and components |
Check the communication system and connections between the controller and components |
| 38-68 |
Wheel setting angles (alignment) not calibrated |
Wheel angle calibration error |
Calibrate the wheel setting angles (alignment) |
| 38-69 |
Actuating mechanisms of lifting and tilting are not calibrated |
Actuating mechanisms calibration error |
Calibrate the actuating mechanisms of lifting and tilting |
| 38-70 |
Power off |
The machine has been powered off |
Check the machine’s power supply and restart if necessary |
| 38-71 |
Battery voltage outside the permissible limits |
Issue with the loader’s battery voltage |
Check and correct the battery voltage to be within permissible limits |
| 38-72 |
Drive Pump Not calibrated |
Issue with the calibration of the drive pump |
Calibrate the drive pump to ensure accurate operation |
| 38-73 |
Control/Motion mode switch is switched on during operation |
Issue with the control/motion mode switch |
Avoid switching the control/motion mode during operation |
| 38-74 |
Speed of the uncontrolled right wheel, erroneous switching on |
Issue with the uncontrolled right wheel’s speed |
Check and repair the speed sensor or wiring for the right wheel |
| 38-75 |
Speed of uncontrolled left wheel, erroneous switching on |
Issue with the uncontrolled left wheel’s speed |
Check and repair the speed sensor or wiring for the left wheel |
| 38-76 |
Control system pressure solenoid-insufficient current |
Issue with the control system pressure solenoid |
Check and ensure sufficient current flow to the control system pressure solenoid |
| 38-77 |
Front right extension control solenoid-insufficient current |
Issue with the front right extension control solenoid |
Check and ensure sufficient current flow to the front right extension control solenoid |
| 38-78 |
Front right retraction control solenoid-insufficient current |
Issue with the front right retraction control solenoid |
Check and ensure sufficient current flow to the front right retraction control solenoid |
| 38-79 |
Forward left solenoid of extension control-insufficient current |
Issue with the front left extension control solenoid |
Check and ensure sufficient current flow to the front left extension control solenoid |
| 38-80 |
Front left solenoid control retraction-insufficient current |
Issue with the front left control retraction solenoid |
Check and ensure sufficient current flow to the front left control retraction solenoid |
| 38-81 |
Rear right extension control solenoid-insufficient current |
Issue with the rear right extension control solenoid |
Check and ensure sufficient current flow to the rear right extension control solenoid |
| 38-82 |
Rear right retraction control solenoid-insufficient current |
Issue with the rear right retraction control solenoid |
Check and ensure sufficient current flow to the rear right retraction control solenoid |
| 38-83 |
Rear left solenoid control-insufficient current |
Issue with the rear left control solenoid |
Check and ensure sufficient current flow to the rear left control solenoid |
| 38-84 |
Rear left solenoid control retraction-insufficient current |
Issue with the rear left control retraction solenoid |
Check and ensure sufficient current flow to the rear left control retraction solenoid |
| 38-85 |
Power supply “1” 5-volt sensor outside the upper boundary of the range |
Issue with the power supply “1” 5-volt sensor |
Check and address the power supply “1” 5-volt sensor if outside the upper boundary of the range |
| 38-86 |
Power supply “2” 5-volt sensor outside the upper boundary of the range |
Issue with the power supply “2” 5-volt sensor |
Check and address the power supply “2” 5-volt sensor if outside the upper boundary of the range |
| 38-87 |
Right front wheel lock (mechanical malfunction control) |
Issue with the right front wheel lock |
Check and repair the mechanical locking mechanism for the right front wheel |
| 38-88 |
Locking of the Left front wheel (mechanical malfunction control) |
Issue with the left front wheel lock |
Check and repair the mechanical locking mechanism for the left front wheel |
| 38-89 |
Right rear wheel lock (mechanical malfunction control) |
Issue with the right rear wheel lock |
Check and repair the mechanical locking mechanism for the right rear wheel |
| 38-90 |
Rear left control error |
Issue with the rear left control |
Check and repair the rear left control |
| 38-91 |
There are no pulses of the right wheel speed sensor |
Issue with the right wheel speed sensor |
Check and repair the right wheel speed sensor |
| 38-92 |
There are no pulses of the left wheel speed sensor |
Issue with the left wheel speed sensor |
Check and repair the left wheel speed sensor |
| 38-93 |
Right wheel speed sensor does not respond |
Issue with the right wheel speed sensor |
Check and ensure proper connection of the right wheel speed sensor |
| 38-94 |
The left wheel speed sensor does not respond |
Issue with the left wheel speed sensor |
Check and ensure proper connection of the left wheel speed sensor |
| 38-98 |
Controller in the drive calibration mode |
Issue with the controller in the drive calibration mode |
Check the controller and exit the drive calibration mode if not required |
| 38-99 |
Controller in wheel position calibration mode |
Issue with the controller in wheel position calibration mode |
Check the controller and exit the wheel position calibration mode if not required |
| 45-03 |
Right turn pointer, erroneous shutdown |
Issue with the right turn pointer |
Check and repair the right turn pointer |
| 46-02 |
Left turn pointer, erroneous inclusion |
Issue with the left turn pointer |
Check and repair the left turn pointer |
| 46-03 |
Left turn pointer, erroneous shutdown |
Issue with the left turn pointer |
Check and repair the left turn pointer |
| 47-21 |
Power supply of 8-volt sensor at the upper limit of the range |
Issue with the power supply of the 8-volt sensor |
Check and address the power supply of the 8-volt sensor if at the upper limit of the range |
| 47-22 |
Power supply of 8-volt sensor, behind the lower boundary of the range |
Issue with the power supply of the 8-volt sensor |
Check and address the power supply of the 8-volt sensor if behind the lower boundary of the range |
| 48-02 |
Front light relays, erroneous switching on |
Issue with the front light relays |
Check and repair the front light relays |
| 48-03 |
Front light relay, erroneous shutdown |
Issue with the front light relay |
Check and repair the front light relay |
| 49-02 |
Rear light relay, erroneous switching on |
Issue with the rear light relay |
Check and repair the rear light relay |
| 49-03 |
Rear light relay, erroneous shutdown |
Issue with the rear light relay |
Check and repair the rear light relay |
| 60-21 |
Signal of the control lever of the back additional Hydraulics at the top of the range |
Issue with the control lever of the back additional hydraulics |
Check and repair the control lever of the back additional hydraulics if at the top of the range |
| 60-22 |
Signal of the control lever of the back additional Hydraulics at the lower limit of the range |
Issue with the control lever of the back additional hydraulics |
Check and repair the control lever of the back additional hydraulics if at the lower limit of the range |
| 60-23 |
Control lever of the back additional hydraulics not returned to the neutral position |
Issue with the control lever of the back additional hydraulics |
Check and repair the control lever of the back additional hydraulics if not returned to the neutral position |
| 64-02 |
Failure to turn on the power relay |
Issue with the power relay |
Check and repair the power relay |
| 64-03 |
Erroneous shutdown of the power relay |
Issue with the power relay |
Check and repair the power relay |
| 74-72 |
Controller boot code failed Bobcat |
Issue with the controller boot code |
Check and repair the controller boot code |
| 74-73 |
Left panel, receiving device error |
Issue with the left panel receiving device |
Check and repair the left panel receiving device |
| 80-02 |
ACD, Exit “A”, erroneous switching on |
Issue with ACD Exit “A” |
Check and repair ACD Exit “A” |
| 80-03 |
ACD, Exit “A”, erroneous shutdown |
Issue with ACD Exit “A” |
Check and repair ACD Exit “A” |
| 81-02 |
ACD, Output “B”, erroneous switching on |
Issue with ACD Output “B” |
Check and repair ACD Output “B” |
| 81-03 |
ACD, Exit “B”, erroneous shutdown |
Issue with ACD Exit “B” |
Check and repair ACD Exit “B” |
| 82-02 |
ACD, Exit “C”, erroneous inclusion |
Issue with ACD Exit “C” |
Check and repair ACD Exit “C” |
| 82-03 |
ACD, Exit “C”, erroneous shutdown |
Issue with ACD Exit “C” |
Check and repair ACD Exit “C” |
| 83-02 |
ACD, Exit “D”, erroneous switching on |
Issue with ACD Exit “D” |
Check and repair ACD Exit “D” |
| 83-03 |
ACD, Exit “D”, erroneous shutdown |
Issue with ACD Exit “D” |
Check and repair ACD Exit “D” |
| 84-02 |
ACD, Output “E”, erroneous switching on |
Issue with ACD Output “E” |
Check and repair ACD Output “E” |
| 84-03 |
ACD, Exit “E”, erroneous shutdown |
Issue with ACD Exit “E” |
Check and repair ACD Exit “E” |
| 90-02 |
Service exit “C”, erroneous switching on |
Issue with Service Exit “C” |
Check and repair Service Exit “C” |
| 90-03 |
Service exit “C”, erroneous shutdown |
Issue with Service Exit “C” |
Check and repair Service |
| 91-02 |
Service exit “D”, erroneous switching on |
Issue with Service Exit “D” |
Check and repair Service Exit “D” |
| 91-03 |
Service exit “D”, erroneous shutdown |
Issue with Service Exit “D” |
Check and repair Service Exit “D” |
| 92-02 |
Service exit “E”, erroneous inclusion |
Issue with Service Exit “E” |
Check and repair Service Exit “E” |
| 92-03 |
Service Output “E”, erroneous shutdown |
Issue with Service Output “E” |
Check and repair Service Output “E” |
| 93-02 |
Service exit “F”, erroneous switching on |
Issue with Service Exit “F” |
Check and repair Service Exit “F” |
| 93-03 |
Service exit “F”, erroneous shutdown |
Issue with Service Exit “F” |
Check and repair Service Exit “F” |